Menu
Allianz and Afloat - Supporting Irish Boating

Ireland's sailing, boating & maritime magazine

In association with ISA Logo Irish Sailing

Displaying items by tag: UK Sailmakers

UK Sailmakers in Cork Harbour have busy fulfilling the many orders for gowns for healthcare workers in the frontline against COVID-19.

As Afloat reported previously, sailmaker Barry Hayes and his team at Crosshaven have been deploying their resources to help make Personal Protective Equipment (PPE) for local healthcare workers at the front line in the fight against this disease.

"We hope the rainbow colours bring a touch of joy to those working tirelessly on the frontline",  Hayes said on social media.

First conceived by UK Sailmakers Norway, the UK lofts in New York, Canada and the Irish loft have made refinements on the design and material selection.

Published in News Update
Tagged under

Barry Hayes from UK Sailmakers Ireland begins a new series of talks with Top Tips For Sailors next Thursday 16 January at Howth Yacht Club from 7.30pm.

Members and guests alike are welcome to attend the two-part session which will cover both optimisation for racing or cruising vessels, and learning how to service your deck hardware — overalls recommended.

Barry will also visit the Royal St George on Thursday 30 January (time TBC) and Kinsale Yacht Club on Thursday 13 February at 7.30pm.

UK Sailmakers Flyer

Published in Howth YC
29th January 2018

Tuning a Fractional Mast & Rig

People seem to think that tuning a fractional rig is very difficult. In reality, it is not that hard as Mark MansfieldProfessional sailor and racing consultant/agent for UK sails Ireland, describes below in the first part of a series of 'How To' articles.

There are four fairly straightforward areas to do and once you go through these is a systematic manner it normally works out fairly well first time. These four areas are:

  • Make sure the rig is in the centre of the boat
  • Make sure the rake is correct
  • Get the prebend right
  • Tighten the shrouds to the correct level

Mark Mansfield 1180Article author Mark Mansfield, Professional sailor and racing consultant/agent for UK sailmakers Ireland Photo: Afloat.ie

I will go through these four in detail in a moment, but whether it is a single spreader, double spreader or triple spreader mast, the system to get it right is the same, just a bit more work with the extra spreaders and shrouds. Also, it is the same whether it is a one design mast like a 1720, Etchells etc. or whether it is a one off custom boat. Most one design classes will have a tuning guide prepared often by a sailmaker and these are certainly a good base point. However, even if you have one of these tuning guides, much of what I will be going through still it very relevant. Over the years I have tuned everything from Admirals cup 45 footers, to Olympic Stars, to Figaro offshore boats to 1720’s, Etchells, Commodores Cup Boats, J109’s and a host of others and though there are small differences between them, the basics remain the same. So let’s go through the four headings above.

CENTRALISE THE RIG

It sounds a very basic and simple thing but it is amazing how many masts are over to one side more than the other. I am taking it that the mast step and the mast gate are in the center (as most are) but if you find having done all the items I mention, that the mast is still not setting up straight, then these should be measured and checked. OK, first thing is to loosen off all the shrouds a good bit until they are relatively loose. Then get a heavyish weight, like a large bucket of water, or a full diesel can and attach it to the Jib halyard. We will be using this to measure from side to side. It is important that you do not use the main halyard as if there is a bit of a bend in the tip, the main halyard will end up over to one side. The jib halyard is where the hounds are and if you can get that point in the center, all the remaining parts of the mast will line up.

Hang the heavy can (attached to the jib halyard) over the side of the boat ensuring that it is not being deflected by the stanchions or guard wires. Mark on this halyard with tape near the shrouds where the rope disappears over the deck. Then bring the halyard around to the other side and see if this tape mark is in the same place, when measured at a similar point. If it is not then you need to loosen the outer shroud on one side and tighten the outer shroud on the other until they are equal. You may need to do this a few times but it is worth the effort.

Now temporarily tighten the outer shrouds nearly back to where they were before you started. Looking up the mast track from behind the mast, tighten up the diagonal shrouds on both sides to ensure the sideways bend in eliminated. Start at the upper diagonal shrouds first, if you have more that one set of spreaders, them move downwards to the lower diagonal shrouds. Once you have the mast looking fairly straight, now we turn our attention to getting the correct mast rake.

cap shroudLooking up the mast track from behind the mast, tighten up the diagonal shrouds on both sides to ensure the sideways bend in eliminated

MAST RAKE

Most modern boats are best set up to about 2.5 to 3 degrees of rake. There are exceptions with some boats only needing one degree and others wanting as much as five degrees. However, the vast majority of boats favor around 2.5 degrees and their keel positions and rig plans are designed around this figure. To measure and adjust your rake, again you will need the bucket of water or other heavy weight. This time hang it from the main halyard until it hangs just below the boom. Ensure the weight aboard the boat is in its normal racing position and get all the crew off the boat. Tighten the backstay to a just taut position. Wait for the bucket to settle and mark where the halyard hits the side of the boom. If the rig is at 2.5 degrees of rake the distance from the back of the mast, measured just above the gooseneck should be circa 4.5% of your P measurement which you will get from your IRC cert. So take a J 109 with an approx. P measurement of 13 metres, 4.5% of this would be 585mm. If your bucket is hanging back further than this, then you need to bring the mast forward by tightening your forestay bottlescrew. If your bucket is hanging closer to the mast than that, then the forestay bottlescrew will need to be loosened. Always ensure you adjust the figures if the main halyard exits to the top of the mast further aft than the main track.

MAST PREBEND & TENSION

OK, So we have the mast now in the middle with the correct rake. Next step is to tighten the shrouds to the correct levels, which should in turn put prebend into the mast. Most sails are cut for a slightly prebent mast with about 1% of P as a decent guide. So, with a J109 with an approx. 13-metre P measurement that means about 130mm of prebend. To measure this, again take your main halyard, attach it to your gooseneck and tighten it hard. Push the halyard against the mast track and look up to see what is the max this halyard is positioned behind the middle of the mast. In the above J109 mast, that should be circa 130mm. If it is more then the diagonal shrouds need to be tightened more to straighten the mast. If it is less then the diagonal shrouds need to be eased. Always remember this is based on your outer (cap) shroud being up to full tension. As you tighten the outer shroud, the mast will likely compress and this will cause bend.

Yacht_J109_Dublin_BayMost modern boats are best set up to about 2.5 to 3 degrees of rake Photo: Afloat.ie

Final tuning of a mast always needs to be done out on the water, preferably with about 12 to 15 knots of wind, with a few bodies on the side. As a general rule the correct tension of the shrouds would be when they just come slack to leeward. If when you go out the leeward shrouds are still bar tight, then you need to ease them a little on both sides. If, as is more likely, the shrouds are too loose, then they need to be tightened, a little on both sides. As the breeze gets stronger it will be difficult to get the shrouds so tight that the leeward shrouds are always hard, especially with an aluminum mast. What happens is as you increase the tension in stronger winds, the mast compresses accordingly and the leeward shrouds stay a bit slack. With a carbon mast, it may be possible however to get the leeward shrouds snug as carbon masts generally bend less from side to side. Getting each individual shroud at the correct tightness level will require quite a few runs side to side, looking up the mast track, trying to see which area is not straight and then adjusting an individual shroud and trying again. Even when the mast is straight, you my find then that there is too much prebend which might necessitate further adjustments to the mast, or may even signal that a small luffround adjustment is needed.

I will be doing a follow-on article on this in a few weeks, which will deal with changing gears on the race course from light winds, right up to very strong winds. For many, finding one decent setting may be what they are looking for, say a medium setting, and then prefer to lock everything off at that stage. Others will want to adjust the rig every couple of knots to try and get that last fraction of speed out of it.

Mark Mansfield—Professional Sailor and racing Consultant/Agent for UK sails Ireland.

e mail[email protected]

UK Sailmakers, in conjunction with the Irish Cruiser Racing Association and Afloat.ie, will be publishing a series of knowledge sharing and how-to articles for the 2018 season.

Published in UK Sailmakers Ireland

#TBSC - Tralee Bay Sailing Club hosted the UK Sailmakers Ireland team of Des McWilliam and Graham Curran on the water for two days of coaching this past weekend (13-14 June).

A series of 16 races was run over the two-day event in Fenit, where a lot was learned and plenty of fun was had by all, as the video above can attest! A photo gallery of the weekend is also available HERE.

Published in News Update

Fastnet Yacht Race 

This race is both a blue riband international yachting fixture and a biennial offshore pilgrimage that attracts crews from all walks of life:- from aspiring sailors to professional crews; all ages and all professions. Some are racing for charity, others for a personal challenge. For the world's top professional sailors, it is a 'must-do' race. For some, it will be their first-ever race, and for others, something they have competed in for over 50 years! The race attracts the most diverse fleet of yachts, from beautiful classic yachts to some of the fastest racing machines on the planet – and everything in between. The testing course passes eight famous landmarks along the route: The Needles, Portland Bill, Start Point, the Lizard, Land’s End, the Fastnet Rock, Bishop’s Rock off the Scillies and Plymouth breakwater (now Cherbourg for 2021 and 2023). After the start in Cowes, the fleet heads westward down The Solent, before exiting into the English Channel at Hurst Castle. The finish is in Plymouth, Devon via the Fastnet Rock, off the southern tip of Ireland.

  • The leg across the Celtic Sea to (and from) the Fastnet Rock is known to be unpredictable and challenging. The competitors are exposed to fast-moving Atlantic weather systems and the fleet often encounter tough conditions
  • Flawless decision-making, determination and total commitment are the essential requirements. Crews have to manage and anticipate the changing tidal and meteorological conditions imposed by the complex course
  • The symbol of the race is the Fastnet Rock, located off the southern coast of Ireland. Also known as the Teardrop of Ireland, the Rock marks an evocative turning point in the challenging race
  • Once sailors reach the Fastnet Rock, they are well over halfway to the finish in Plymouth.
  • The lighthouse first shone its light on New Year’s Day in 1854
    Fastnet Rock originally had six keepers (now unmanned), with four on the rock at a time with the other two on leave. Each man did four weeks on, two weeks off

At A Glance – Fastnet Race

  • The world's largest offshore yacht race
  • The biennial race is 605 nautical miles - Cowes, Fastnet Rock, Plymouth
  • A fleet of over 400 yachts regularly will take part
  • The international fleet is made up of over 26 countries
  • Multihull course record: 1 day, 8 hours, 48 minutes (2011, Banque Populaire V)
  • Monohull course record: 1 day, 18 hours, 39 minutes (2011, Volvo 70, Abu Dhabi)
  • Largest IRC Rated boat is the 100ft (30.48m) Scallywag 100 (HKG)
  • Some of the Smallest boats in the fleet are 30 footers
  • Rolex SA has been a longstanding sponsor of the race since 2001
  • The first race was in 1925 with 7 boats. The Royal Ocean Racing Club was set up as a result

Featured Sailing School

INSS sidebutton

Featured Clubs

dbsc mainbutton
Howth Yacht Club
Kinsale Yacht Club
National Yacht Club
Royal Cork Yacht Club
Royal Irish Yacht club
Royal Saint George Yacht Club

Featured Brokers

leinster sidebutton

Featured Webcams

Featured Car Brands

subaru sidebutton

Featured Associations

ISA sidebutton dob
ICRA
isora sidebutton

Featured Events 2020

Wave button for Afloat new dates

Featured Chandleries

CHMarine Afloat logo
osm sidebutton
viking sidebutton

Featured Sailmakers

northsails sidebutton
uksails sidebutton

quantum sidebutton

Featured Marinas

dlmarina sidebutton

Featured Blogs

W M Nixon - Sailing on Saturday
podcast sidebutton
mansfield sidebutton
BSB sidebutton
sellingboat sidebutton

Please show your support for Afloat by donating